Api-delevan BF Series Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Api-delevan BF Series. API Delevan BF Series User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 3
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
BF SERIES
Split Ferrite Suppressors for Round Cables
Suppressors
270 Quaker Rd., East Aurora NY 14052 • Phone 716-652-3600 • Fax 716-652-4814 • E-mail: apisales@delevan
.
com • www.delevan.com
Electronic cables and wires, by virtue of their length-to-width
ratios, are perfect natural antennas. In the presence of high
speed microprocessor signals, cables will conduct, radiate
and/or receive unwanted high frequency interfering signals.
Radio interference sources usually radiate their RFI power at
frequencies above 30 MHz by way of the main cabling, which
acts as an antenna. Control of radio interference can be
assured by proper placement of an insertion loss device, such
as a ferrite suppressor. Any device used to block an RFI signal
between its source and a receiver is an electromagnetic
interference (EMI) shield. The measure of this ability to
attenuate RFI is shielding effectiveness, "SE", which is
expressed in decibels, "dB", the ratio of field strength on one
side of the shield to the other side.
One of the most versatile and cost effective shielding methods
that can be used today is the API Delevan bisected ferrite cable
snap assembly. The bisected styling, or familiar clamshell
enclosure design offers the ultimate in adaptability. The RF
absorbing material interacts directly with unwanted high
frequency energy and dissipates it effectively while allowing
data signals to pass unimpeded.
Bisected ferrites have a concentrated, homogeneous magnetic
structure with high permeability. These are consistently stable at
+20°C to +60°C and provide RF suppression without eddy
current losses.
AIR GAP EFFECT
The air gap in bisected ferrites actually extends current carrying
capabilities with only an extremely small reduction in
impedance versus solid ferrites of the same size. The gap is
magnetically insignificant while it is electrically significant as a
discontinuation, thereby accommodating more current.
POSITION OF SUPPRESSOR The suppressor should normally
be located close to the cable termination where it exits the
enclosure. Where a cable connects two enclosures containing RF
sources, a suppressor on each end may be required. For circuits
within an enclosure, a position close to the RF is best. However,
other locations along the circuit may work as well.
Material and U.L. Data API-1 Material, see characteristics and
information in the Technical Notes Section of our website,
www.delevan.com.
Continued on next page
Actual Size
(BF2125)
Actual Size
(BF2125)
1/2009
API_newlayouts_single:APIcatalog_newlayouts 8/27/10 10:01 AM Page 118
Vue de la page 0
1 2 3

Résumé du contenu

Page 1 - BF SERIES

BF SERIESSplit Ferrite Suppressors for Round CablesSuppressors270 Quaker Rd., East Aurora NY 14052 • Phone 716-652-3600 • Fax 716-652-4814 • E-m

Page 2

BPART NUMBERUNITSBODY TYPEA25 MHz100 MHzSuppressors270 Quaker Rd., East Aurora NY 14052 • Phone 716-652-3600 • Fax 716-652-4814 • E-mail: apisal

Page 3

Suppressors270 Quaker Rd., East Aurora NY 14052 • Phone 716-652-3600 • Fax 716-652-4814 • E-mail: [email protected] • www.delevan.com BF SE

Commentaires sur ces manuels

Pas de commentaire